A common inlet at the top feeds two (identical) centrifugal fans. I tried to connect Top_System_inlet_interface (identical to but different in name as suction outlet interface) to serve double-duty as outlet interface to both the Top_Fan (rotating) AND Bottom_Fan (rotating).

It seemed that wasn't working so it occurred to me that connecting a copy of the object with another name might. Sure enough! It seems to have worked.

How would you have done it?

Hi contributors,

I sincerely appreciate your team's efforts in making your work publicly available online—it has been immensely helpful for OpenFOAM users and developers alike. After reading your article (Node266 - CFD SUPPORT), I followed the provided instructions to configure OpenFOAM to generate a cellZone using snappyHexMesh.

Unfortunately, the attempt was unsuccessful. The number of cells in both the cellZone and faceZones files turned out to be zero, and checkMesh.log confirms this issue. When I check the result via paraFoam, I also find that net0 ~ net4 contain no mesh—they are empty. This is not only contrary to my expectations, but also differs from the result described in the article.

I am using OpenFOAM v2012, and the net0 section in my snappyHexMeshDict was set up following the example from your webpage.

I’ve uploaded the relevant case below. I would greatly appreciate any guidance.

--------------------------------------------------------------------------------------------------

snappyhexmeshdict:

/*--------------------------------*- C++ -*----------------------------------*\
| =========                 |                                                 |
| \\      /  F ield         | OpenFOAM: The Open Source CFD Toolbox           |
|  \\    /   O peration     | Version:  v2012                                 |
|   \\  /    A nd           | Website:  www.openfoam.com                      |
|    \\/     M anipulation  |                                                 |
\*---------------------------------------------------------------------------*/
FoamFile
{
    version     2.0;
    format      ascii;
    class       dictionary;
    object      snappyHexMeshDict;
}
// * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * //
#include "../varsSettings" //Include global variables
castellatedMesh true;
snap            true;
addLayers       false;//true;
geometry
{
    floater
    {
        type 	triSurfaceMesh;
        file 	"DeepCwindPlatform_heave.stl";
    }
    
    net1
    {
        type 	triSurfaceMesh;
        file 	"Net1_improved_heave.stl";
    }
    
    net2
    {
        type 	triSurfaceMesh;
        file 	"Net2_improved_heave.stl";
    }
    
    net3
    {
        type 	triSurfaceMesh;
        file 	"Net3_improved_heave.stl";
    }
    
    net4
    {
        type 	triSurfaceMesh;
        file 	"Net4_improved_heave.stl";
    }
    
    net0
    {
    	type	searchableBox;
    	min		(-100	-50	-120);
    	max		(100	50	-80);
    }
    
    refineFreeSurface_L1
    {
        type searchableBox;
        min ($minX  $minY -10);
        max ($maxX  $maxY  10); 
    }
    
    refineFreeSurface_L2
    {
        type searchableBox;
        min (#calc "$minX+$inLen+20"  -70 -8);
        max (#calc "$maxX-$outLen-20"  70  8); 
    }
    
    refineFloater_L1
    {
        type searchableBox;
        min (-51  -49	#calc "-30 + $decay_z + $offset_z");
        max ( 37   49 	#calc "22 + $decay_z + $offset_z"); 
    }
};
castellatedMeshControls
{
    maxLocalCells 100000;
    maxGlobalCells 2000000;
    minRefinementCells 0;
    maxLoadUnbalance 0.10;
    nCellsBetweenLevels 1;
    features
    (
        {
        	file    "DeepCwindPlatform_heave.eMesh";
            level   4;
        }
        
		{
        	file	"Net1_improved_heave.eMesh";
        	level	4;
		}
		
		{
        	file	"Net2_improved_heave.eMesh";
        	level	4;
		}
		
		{
        	file	"Net3_improved_heave.eMesh";
        	level	4;
		}
		
		{
        	file	"Net4_improved_heave.eMesh";
        	level	4;
		}
    );
    refinementSurfaces
    {
		floater
		{
			level (4 4);//(5 5);
			patchInfo
        	{
          		type wall;
 
          		// Optional group
          		// inGroups (meshedWalls);
        	}
		}
          
		net1
    	{
			level (4 4);
			cellZone net1Zone;
/*			cellZoneInside inside;*/
			faceZones net1fZone;
    	}
    	net2
    	{
        	level (4 4);
			cellZone net2Zone;
/*			cellZoneInside inside;*/
			faceZones net2fZone;
    	}
    	net3
    	{
        	level (4 4);
			cellZone net3Zone;
/*			cellZoneInside inside;*/
			faceZones net3fZone;
		}
    	net4
    	{
        	level (4 4);
			cellZone net4Zone;
/*			cellZoneInside inside;*/
			faceZones net4fZone;
    	}
    	
    	net0
    	{
        	level (4 4);
			cellZone net0Zone;
/*			cellZoneInside inside;*/
			faceZones net0fZone;
    	}
    }
    resolveFeatureAngle 45;//30;
    planarAngle 30;
    refinementRegions
    {
        refineFreeSurface_L1
        {
            mode inside;
            levels ((1e-5 1)); //First entry here is distance, which will be ignored unless mode = distance
        }
        
        refineFreeSurface_L2
        {
            mode inside;
            levels ((1e-5 2)); //First entry here is distance, which will be ignored unless mode = distance
        }
        
        refineFloater_L1
        {
            mode inside;
            levels ((1e-5 2)); //First entry here is distance, which will be ignored unless mode = distance
        }
        
/*        net1*/
/*        {*/
/*            mode inside;*/
/*            levels ((1e-5 3));  // STL 内部 refinement 到 level 4*/
/*        }*/
/*        net2*/
/*        {*/
/*            mode inside;*/
/*            levels ((1e-5 3));*/
/*        }*/
/*        net3*/
/*        {*/
/*            mode inside;*/
/*            levels ((1e-5 3));*/
/*        }*/
/*        net4*/
/*        {*/
/*            mode inside;*/
/*            levels ((1e-5 3));*/
/*        }*/
    }
    limitRegions
    {
    }
        locationInMesh (-150 0 0);
        allowFreeStandingZoneFaces true;//false;
        faceZoneControls
        {
        }
    locationsOutsideMesh ((100 100 100));
}
snapControls
{
    nSmoothPatch 5;//3
    tolerance 2.0;
    nSolveIter 50;//30;
    nRelaxIter 10;//5;
        nFeatureSnapIter 20;//10;
        implicitFeatureSnap false;//true;
        explicitFeatureSnap true;//false;
        multiRegionFeatureSnap false;
}
addLayersControls
{
    relativeSizes true;
        expansionRatio 1.25;
        finalLayerThickness 0.64;
    	minThickness 0.1;
    layers
    {
		floater
		{
			nSurfaceLayers    2;//3;
		}
    }
    nGrow 0;
        featureAngle 180;//180;
        maxFaceThicknessRatio 0.5;//0.5;
        nSmoothSurfaceNormals 1;
        nSmoothThickness 10;
        minMedialAxisAngle 90;
        maxThicknessToMedialRatio 0.3;
        nSmoothNormals 3;
        slipFeatureAngle 30;
        nRelaxIter 5;
        nBufferCellsNoExtrude 0;
        nLayerIter 50;
        nRelaxedIter 20;
}
meshQualityControls
{
    #include "meshQualityDict"
    relaxed
    {
        maxNonOrtho 75;
    }
        nSmoothScale 4;
        errorReduction 0.75;
}
mergeTolerance 1e-6;
// ************************************************************************* //

Thank you very much in advance!

Best regards,

Liu Jiaming

The instructions are as follows:

To create two meridional slices, one for each fan in TCAE, follow these step-by-step instructions:

1. Load the Simulation Results: Open your TCAE project and load the results of your simulation for the fans.

2. Select the First Fan:

   • In the Pipeline Browser, select the mesh or results corresponding to the first fan.

3. Add a Meridional Average Filter:

   • Go to the Filters menu.
   • Select "Turbomachinery" and then choose "Meridional Average."

I am not presently seeing any geometry in the Pipeline Browser, so, I tried double-clicking the individual STLs making up the component in CFD Mesh, (later realizing selecting multiple elements is not supported) then going to the Filters menu, selecting Turbomachinery,  the option "Meridional Average."  is greyed out, please see image.

I'm still at the beginning setup phase; loading geometry and tweaking types and interfaces. I have no results of any simulation to load. I have not tried to create a mesh yet. Is that (or something else) I need to do first besides read the manual?

Thanks in advance

David

After reimporting surface geometry, I see that the legend for the color bar in Reader View has multiple color bar legends superimposed. Can I, should I hide one or the other?

If so, how?

Thanks,

David

I'm not wanting to re-import geometry, although that's most certainly what I'm preparing for at the moment. All the STLs were created using the _ExportWithOrigin command with World origin as basepoint in Rhino, so I'm scratching my head, as usual. Importing the offending object back into a "top" drawing, an assembly-of-all-parts model, and aligning it to it's exact position, then re-exporting it and replace the file having the wrong origin is what I'll try next.

Is there any easy way to manipulate objects once they've been imported?

Please see my comment, button at bottom right. Thanks.

is it possible with TCAE to make “overmesh” meshes?

Hi All,

New user here. I've gone through the tutorials and forum but haven't found my answer. Asking the AI chat bot it says I need to do some scripting and change some files, which I don't believe. I feel the answer is more straight forward.

How do I measure the mass flow rate through my system? You can set the units for the report, but my report shows nothing of the sort. I'm sure there must be something simple like a button to calculate this?

Hi,

I'm a new user of TCAE-Lite.

I've setup a pump case and the "check" button says the case has been setup correctly. However it fails to mesh.

The same error occurs when running the f1 tutorial case.

Any advice would be appreciated,

Thanks,

Tom

Hi! I'm a beginner CFD user, and I've encountered a strange bug with my mesh. When I reduce the firstLayerThickness to a smaller value, the mesh stops working. The layer doesn't generate properly, and I get an error saying my refineBox isn't inside my blockMesh, which is incorrect.

Hi everyone,

I woud like to export the relative velocity URel magnitude, instead of the absolute velocity U magnitude, in the interfaces files created by TCAE in ../stationnary/postProcessing/interfaceName/0/interfaces.csv. I tried to change the file ./stationnary/system/interfaces. fun by replacing magU by magURel in the list of fields per interface but it did'nt work... How can I do it ?

Thanks in advance !

Zacharie Prigent

Hi Foamers, 

Based on the given instructions underneath, I have been able to come up with this design. Could you help confirm if the attached image to this topic looks promising or requires some modifications? Thanks 😊 

“Introduction

Finishing a small meshing task is the first possibility multi-block mesh using the blockMesh utility or Salome,

e. The task, creation of a small

Geometry

wall

outlet

cut

inlet

Z

Parameters d=50.8 mm

I=508 mm a=12.7 mm

= a/2

Description

The geometry represents half of the 2" pipe inner volume. It is composed of four building blocks. The first block (No. 1) represents the core of the pipe. The other blocks (No. 2, 3, and 4) fill the outside pipe volume.

The mesh blocks must be split by more than one cell in every direction. You can select how many cells you want to use. Apply the mesh grading, if possible.

The outside volume surfaces are called inlet, outlet, wall, and cut. Select an appropriate patch type for each surface.

The blockMesh utility writes out a log. Ensure no errors are reported.

Hint: The local coordinate system in each block should be aligned with the global coordinate system!”

I ma trying to create a thin boundary layer, to achieve a yplus <1 and I need the first cell to be positioned at 10^-5 from the wall of my 3D airfoil. I created the mesh using blockmesh and now I want to use snappyhexmesh only the add layer function.However when I do this snappyhexmesh does not generate the boundary layer. Thank you

Nicolas